Gas fireplace service
Sweep & inspection
Caps & crowns
Flue relining
Masonry repairLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Why East New York Homeowners Choose DuraFlex Chimney Cleaning
We provide independent DuraFlex chimney cleaning and service in East New York, NY. DuraFlex is a flexible stainless steel chimney liner, and our work on it goes past sweeping: we clear glazed creosote out of corrugated walls, reseat top plates and adapters, replace failed insulation wrap, and tell you honestly when a liner has reached the end of its run. Our technicians have up to 12 years of experience with flexible liner systems, and we inspect before we recommend anything.
To be clear about who we are: Chimney Sweep East New York is an independent service provider. We are not affiliated with, authorized by, or a dealer for DuraFlex, and nothing we do carries the manufacturer’s endorsement. What we offer is hands-on familiarity with how these liners behave in East New York’s pre-war rowhouse stock, plus the professional-grade materials to fix them properly. Call (855) 337-0826. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Why Trust Chimney Sweep East New York for Your DuraFlex Chimney Cleaning?
DuraFlex liners show up in this part of Brooklyn often enough that we know their habits. Corrugated stainless collects creosote differently than smooth-wall product. Insulation wrap pulls back at thimbles and offsets in ways you only learn by opening a lot of chimneys. When we sweep a DuraFlex flue, we’re reading the liner while we clean it: checking ridge depth for glazing, looking for pitting along the seams, and feeling for the soft spots that mean condensation has been eating the steel from the inside.
We use quality parts that fit DuraFlex equipment, including top plates, caps, adapters, and insulation wraps sized to match the liner’s corrugation pitch. That matters for your warranty. Improper cleaning methods or mismatched hardware are exactly the kind of thing a manufacturer can point to when a claim comes in, so we work in a way that keeps your coverage intact and document what we find with a camera inspection and photo report. Proper repair, not a patch.
Our technicians have up to 12 years of experience across the full chimney system, from sweeping and Level 2 inspection to cap and crown work to fireplace repair. One call covers the whole job, which means nothing gets handed off mid-project or skipped because it fell outside someone’s scope.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Common DuraFlex Chimney Cleaning Problems We Fix in East New York
These are the DuraFlex issues we run into most in East New York, and why they happen.
- Glazed creosote packed into the corrugations. In wood-burning service, the ridges of a standard corrugated 316L stainless liner trap hard, shiny creosote that a standard brush skips right over. It’s difficult to sweep and it accelerates pitting corrosion underneath. Removing it takes poly rotary brushes sized to the liner diameter, worked at a controlled speed so the stainless isn’t abraded in the process.
- Insulation wrap separating at thimbles and offsets. On insulated flexible liner kits, the factory insulation wrap can degrade or pull away where the liner passes through a wall thimble or bends through an offset. Those uninsulated sections run cold, condensation forms on the steel, and rust-through follows. It’s one of the most common hidden failures we find, because it happens out of sight.
- Collar cracks on smooth-wall liners. SmoothWall liners can crack at the flue collar where they’re flexed over a clay tile lip, particularly when the original install skipped a proper top plate or adapter. A crack there lets flue gases and moisture escape into the chimney chase instead of up the flue.
- Surface spalling and pinholes in lower-grade sections. Stainless rated for wood and appliance use can develop surface spalling and pinholes after years of flue-gas condensation, especially in chimneys that are under-fired or venting appliances that don’t run hot enough to keep the flue dry. Small holes become bigger ones fast.
- Water intrusion from a loose or missing top plate or cap. A surprising share of liner problems start at the top. A cap that’s blown loose or a top plate that was never sealed lets rain straight down the flue, and the liner takes the damage. This is why cap installation and a Level 2 inspection belong in the same visit as the sweep.
A typical DuraFlex call in a pre-war East New York rowhouse starts with a homeowner noticing smoke rollout or a strong creosote odor from a wood-burning fireplace lined with a corrugated 316L flexible liner. On inspection, the sweep finds glazed creosote packed into the liner’s ridges and often a loose or missing top plate or cap allowing water in. A qualified independent sweep typically performs a Level 2 inspection, uses poly rotary brushes sized for the liner diameter to remove the glazed creosote without abrading the stainless, then reseats or replaces the top plate and cap to stop the water intrusion.
East New York’s housing stock makes all of this worse. The neighborhood is dominated by 1920s – 1940s semi-detached brick houses and small apartment buildings, many with exterior chimneys that have never been relined and a large share of rentals where maintenance gets deferred. Cold winters and freeze-thaw cycles crack mortar crowns and chimney caps, while humid summers promote spalling and efflorescence on the soft older brick. On many blocks the chimney serves only the basement boiler, so a liner that looks fine from the fireplace can be quietly failing on the heating side. Technicians here routinely find bird nests and crumbling mortar in flues that haven’t seen a brush in decades.
DuraFlex Parts & Our Repair-vs-Replace Approach
For DuraFlex repairs, we use genuine DuraFlex components: top plates, caps, adapters, and insulation wraps. Aftermarket flexible-liner hardware often doesn’t match the corrugation pitch, and a mismatched plate or adapter is how you get leaks and poor fit. We don’t claim to stock OEM parts; we source what fits your liner and install it correctly.
The repair-or-replace decision comes down to how much of the liner has actually failed. A cracked collar, a loose top plate, a short stretch of pulled-back insulation: those are repairs, and we’ll make them. But if the liner is pitted through, or the insulation has failed over a significant run, honest replacement with a correctly sized DuraFlex kit is usually the more cost-effective path. Patching section by section on a liner that’s already compromised just moves the problem down the flue. You’ll see the camera evidence before we recommend either way, and if the work can safely wait, we’ll tell you that too. Call (855) 337-0826 for a free estimate.
Our DuraFlex Service Process – Step by Step
- 1
Diagnosis. We start with a Level 2 inspection: camera through the flue, a look at the liner’s interior surface, the top plate, the cap, and every point where the liner passes through a thimble or offset. Glazed creosote, pitting, and insulation pull-back all show up here. You get the photo report.
- 2
Repair or install. Depending on what the inspection shows, we sweep with rotary brushes sized for the liner, reseat or replace the top plate and adapter, replace insulation wrap, or install a correctly sized DuraFlex liner where replacement is the right call. Caps go on sealed and fitted to the flue.
- 3
Test. We check draft, confirm the cap and top plate are watertight, and verify the liner is clear end to end. On a boiler vent, that includes confirming the appliance is drafting properly and there’s no backdraft risk.
- 4
Warranty. You get documentation of the work and the materials used, which is what a manufacturer needs if a warranty question ever comes up. Proper method and matched components keep your coverage where it belongs.
See the difference
Before
After
Before
After
Before
AfterDuraFlex Products We Service & Install in East New York
We service and install the DuraFlex flexible stainless liner range as it’s used in East New York homes: standard corrugated 316L stainless liners in wood-burning fireplaces, 304L stainless liners on wood and appliance runs, Pro Series insulated flexible liner kits, and SmoothWall liners where a smoother interior surface matters. That covers the liner itself, plus the top plates, caps, adapters, and insulation wraps that make the system work as a unit.
Your chimney is a system, not just a flue. A liner that’s perfect at the bottom and missing a cap at the top is still a failing chimney.
We Also Service These Brands
DuraFlex is one of six professional brands we work with, alongside HeatShield, Gelco, Olympia Chimney, Famco, and Copperfield. HeatShield gives us a resurfacing option for restoration without full relining, and Gelco covers the cast-cement side of repair work. Being multi-brand matters: we recommend the material that fits your chimney, not the only one we happen to carry.
FAQs – DuraFlex Chimney Cleaning Service in East New York
No. We are an independent service provider with no affiliation to, authorization from, or dealer relationship with DuraFlex. We service and install their liners because they’re widely used in East New York, not because the manufacturer endorses us. Our credibility comes from the work and the inspection evidence, not a badge.
Yes. We use genuine DuraFlex components for DuraFlex repairs, including top plates, caps, adapters, and insulation wraps sized to match the liner’s corrugation pitch. We don’t stock OEM parts, and we don’t substitute aftermarket hardware that doesn’t fit, since mismatched components are a leading cause of leaks and warranty problems.
Most DuraFlex sweeps and inspections take a couple of hours, and repairs like reseating a top plate or replacing a cap usually fit in the same visit. A full reline takes longer and gets scheduled as its own job. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. Call (855) 337-0826 to get on the schedule.
Not necessarily. That coating is glazed creosote, and in most cases it can be removed with poly rotary brushes sized to the liner diameter without damaging the stainless. Replacement only becomes the answer when the corrosion underneath has gone too deep. The way to know is a camera inspection, and you’ll see the footage before we recommend anything. Call (855) 337-0826 for a free estimate.
Almost always a top plate or cap problem. A cap that’s blown loose, a plate that was never sealed, or an adapter that doesn’t match the flue opening lets rain run straight down the liner. Resealing or replacing those components usually solves it. Left alone, the water rusts the liner from the inside. Call (855) 337-0826 and we’ll take a look.
Often yes, if the crack is isolated to the collar area and the rest of the liner is sound. The repair means fitting a proper top plate or adapter so the liner isn’t flexed over a bare clay tile lip. If the crack has spread or the liner is pitted nearby, replacement is the honest answer. Call (855) 337-0826 for a free estimate and we’ll show you which one it is.
There’s no single size. It depends on the flue’s dimensions, the appliance it serves, and whether the run is wood-burning or venting a boiler. Sizing gets worked out during the Level 2 inspection, which is why we don’t quote a liner over the phone.
It needs a cap that fits the top plate and seals properly against water, and the plate has to match the insulated liner’s outside diameter. A standard cap clamped over an insulated kit without the right plate leaves gaps. We fit caps to the actual liner and flue, not the other way around.
Improper cleaning or mismatched hardware can compromise a warranty claim; correct service generally doesn’t. We clean with brushes sized for the liner, use components that match it, and document the work so there’s a record if a question ever comes up. That’s part of why we inspect before we recommend.
Most DuraFlex sweeps and Level 2 inspections in East New York land in a few hundred dollars range, with the written estimate setting the final price before any work starts. The estimate is free, and nothing gets recommended without camera evidence you can see. Call (855) 337-0826 for an exact quote.
Book Your DuraFlex Service in East New York, NY
If you’ve got a DuraFlex liner and you’re not sure of its condition, a Level 2 inspection settles it. We’ll sweep what needs sweeping, show you the camera footage, and tell you plainly whether it’s a repair, a replacement, or something that can wait. Call (855) 337-0826 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Chimney Sweep East New York.